Check out our new online store at www.yourdci.com

E10-npn : The World's Smallest Ladder Programmable Controller

Photograph of E10-npn and E10-Relay
E10-npn is Only 5.4cm x 5.4cm x 2.0cm

Technical Specifications

E10-npn

12 to 30V DC Power Supply

6 Inputs with LED Indicators (12~30V DC, NPN type)

4 Outputs (each output can sink 1A @ 12~30V DC)

8 internal relays+2 internal outputs

4 timers (0.1s to 25.4s) 4 counters(1 to 254)

1 sequencer with 32 steps (step#0 - #31)

90 program steps (1 contact = 1 step)

Programmable in Ladder Logic software With SIMULATOR.

Creates ladder program using meaningful names:-
- Uses simulator to fully test programs on the PC screen before downloading
- On-line monitoring of all I/O logic states on ladder diagram or on full screen
- Forced-setting/resetting of i/os can be done directly from computer screen.
- EEPROM Program Storage (40 years)
- Screw Terminal Blocks

E10-Relay

24V AC (0.3A transformer)

6 Inputs with LED Indicators (24V DC, PNP type)

4 relay Outputs (2 commons. Each output can switch 2A @ 250V AC)

All the rest are same as E10-npn.

I. Introduction

Finally, a ladder logic programmable controller so small and cost so little that it can effectively replace all those bulky relays, timers or counters found in your current control panels. Its 24V DC transistor outputs or 0 to 250V AC relay outputs eliminate the need for additional driver circuitry and its incredibly low price means you actually save money while getting a technically superior design for your next control panel project! Despite its simple appearance, the E10's share equally sophisticated programming tools with their larger siblings - The H-series which comprise the T20H with 12 inputs / 8 outputs to the T64H with 40 inputs and 24 outputs.

An E10 is programmable using an extremely user-friendly ladder logic editor/simulator software - TRiLOGI. TRiLOGI runs on any IBM PC compatible computer. Featuring pull-down menus, pop-up windows and on-line context-sensitive help systems, TRiLOGI is the most user-friendly ladder logic editor available. Its built-in logic SIMULATOR allows you to perform complete off-line testing of your program on your PC screen without connecting to the target PLC.

II. Hardware Specifications

E10-Relay

E10-npn

1.

Power Supply
- AC 24V (current = 0.2A)
- Rectified DC24V available for sensor. - DC 12 to 30V (+ 10% ripple)
- Current 0.5~2A (load dependent)

CPU only current consumption 20mA 20mA

2. CPU

Program Storage Size 90 steps stored in EEPROM 90 steps stored in EEPROM

Average Execution Speed 20盜 per step 20盜 per step

3. Input Circuits

Number of inputs 6 (PNP type) 6 (NPN type)

Input Voltage for Logic 0 open circuit or 0 to 3.5V DC open circuit or 8.5V to 24V

Input Voltage for Logic 1 8 to 24V DC 0V to +3.5V DC

4. Output Circuits

Number of outputs 4 4

Peak output current 2.0A @250VAC or 30VDC per output Sink 1.0A per output

Output Voltage for Logic 1 Dry contact 1.2V @ Iout = 500mA

Inductive back EMF protection ---- No---- -----yes----

5. Dimension 7.8cm (L) x 5.6cm (W) x 2.5cm(H) 5.4cm (L) x 5.4cm (W) x 2.0cm(H)

6. Weight (approximate) 75g 35g

III. Software Features and Programming Methods

	View Software Features For E Series
	Download a fully functional free copy of TRiLOGI Software for your evaluation!

IV. E10-npn Wiring Diagram

	Wiring Diagram (This diagram shows the previous board layout, but the terminal block connections are the same as the updated board shown below)
	E10-npn and E10-Relay Installation Guide - "inst-e10.zip" (111K)

V. Starter Kits

To help new users get started quickly, we package Starter Kits for different models which includes practically all the hardware and software (except power supply) needed to start using the boards.


ORDER HERE

File Download Summary Page

HOME

Contents

Contact Us

Search

Read Legal Info Here "DCI Technologies", "Micro-CAPP" and "COR-Logic" are Trademarks of DCI Technologies Inc. All other trademarks are property of their respective owners. Last modified July 29, 2008 (nfdotca)